Water Pipes Search Results

How To: Solder stainless steel

This video tutorial is in the Electronics category which will show you how to solder stainless steel. For this you will need silver bearing solder. Harris #8 StaBrite is good, but it is expensive. Plumber solder works fine, but make sure it has silver in it. Use Harris Stay Clean liquid flux. All the surfaces have to be clean and sanded. In this video a pipe is being soldered to a metal sheet. Apply some liquid flux to the outside of the pipe to be soldered. Make a neutral flame, heat the pip...

How To: Make movie rain without getting wet

In this tutorial, we learn how to make movie rain without getting wet. First, you will need to get a garden hose that has a spout on it and few pieces of PVC pipe. Connect the pieces of PVC pipe together, then stick the head of the hose to the pipe. Keep in mind that you will want to cut the pipe a bit shorter so it's easier to hold. Now, have someone hold up the pipe while you are taping and make sure to stay opposite of the way the wind is blowing. After this, you will have taped rain in a ...

How To: Craft a lily flower out of paper & pipe cleaner

In this tutorial, we learn how to make a lily out of paper and pipe cleaner. First, lay your hand flat on a piece of copy paper. Next, trace your hand with a pen or pencil, then cut it out with scissors. Now use a pencil or pen to curl the ends of the fingers you just cut out. After this, combine two pieces of gold pipe cleaner together and bend in half. Then, place a green pipe cleaner in the middle and make a twist to keep in place. To finish, wrap your paper hand cut out around the gold pi...

How To: Craft a penguin out of pipe cleaners

In this tutorial, we learn how to craft a penguin out of pip cleaners. First, grab a pencil and wrap white pipe cleaner around the top. Now, wrap black around the pencil as well, and squish them both together. Slide them off, then take an orange pipe cleaner and fold it in half. About 2 rings from the top of the black, poke the orange through that will be the beak. On the bottom, twist the orange pip cleaner together to make penguin feet, then clip off any excess pipe cleaner. Now, take black...

How To: Craft a snake out of pipe cleaner

In this tutorial, we learn how to craft a snake out of a pipe cleaner. First, you will take three pipe cleaners and twist their ends together, then stick a large pom pom in between the pipe cleaners. Then do a braid with the pipe cleaners until you reach the end, and then twist the end together. Then, take some googly eyes and glue them onto the pom pom. You can now twist the snake to make it look like a rattle snake and add a piece of red felt to make the tongue. This is a fast and easy proj...

How To: Build your own green screen

In this video tutorial, viewers learn how to build a green screen. The materials required for this project are: two 10 ft long PVC pipes, measuring tape, saw, duct tape and pipe elbows and couplings. Begin by marking the two PVC pipes with 6 ft on one side and 4ft on the other. Then cut the PVC pipes in half. Now connect the frame together with the pipe elbows and couplings. Build support to the fame by adding some duct tape. Finish by attaching the green cloth on the frame and tape it at the...

How To: Build a skateboard half-pipe with Michael Strahan

Building your own skateboard half-pipe in the confines of your own backyard, is a great thing for anyone who enjoys a little challenge. Certain weather conditions or travel issues, can make it difficult for some skateboarders who are looking to spend some quality time trying new tricks and perfecting skills. In this tutorial, you'll find out how to build a skateboard half-pipe with the help of former NFL star, Michael Strahan. So good luck and enjoy!

How To: Cut copper pipe with the right tools

This shirt video will show you how to cut copper pipe with the right tools. Cutting copper pipe is simple if you have the right tools. This short video clip clearly demonstrates how to go about cutting copper tubes. Among other things you will be using a pipe slice. The video also shows you how to remove the burrs before attempting to join the pipe. You are advised to never use a hacksaw.

How To: Use compression fittings on copper pipe

Copper pipe is perhaps the most versatile of all piping types in that you can use virtually any fitting with it. Copper pipe, however, is not particularly flexible, which can make it a little unwieldy to work with. Simplify your copper piping projects by using compression fittings. This home plumbing video tutorial shows you how. For detailed, step-by-step instructions on using compression joints in your copper plumbing projects, take a look.

How To: Use push-fit joints on copper pipe

Copper pipe is perhaps the most versatile of all piping types in that you can use virtually any fitting with it. Copper pipe, however, is not particularly flexible, which can make it a little unwieldy to work with. Simplify your copper piping projects by using push-fit fittings. This home plumbing video tutorial shows you how. For detailed, step-by-step instructions on using push-fit joints in your copper plumbing projects, take a look.

How To: Make pipe cleaner action figures

In this series of crafts videos, our young comics and science fiction fan (and professional actor) Halley Joseph Eveland will talk you through the creation of pipe cleaner action figures. As you bend, twist and snip your colored pipe cleaners, watch these fun versions of your favorite Star Wars heroes take shape before your very eyes. And these are not simply stick figures, but artistic creations with muscles, capes, masks and of course light sabers.

How To: Freeze water by boiling acetone

You can freeze water by boiling it. To do this you will need a Vacuum pump. Vacuum pump can be used to suck out air from a container and create vacuum in it. Take a bell jar. Now connect the vacuum pipe into it and suck out the air from it. Take a flash and add little bit of water to it. Now we want to freeze this water. Add some acetone to it. Acetone boils and evaporates very quickly. Add a few chips of marble to it. These will enable in boiling of the water. Now set this flask in the bell ...

How To: Bust a 900 on skis with Tanner Hall in a pipe

When you're skiing in a quarter pipe you want to watch your landing. You're going to drop the shoulder and hold the body position of your spin. Spot the landing. Be comfortable on the pipe and landing 720s before you try the 900. You never want to land a flat bottom on a 900 cause it will hurt you.

How To: Decorate a cake with piped scrolls of icing

This video cake decorating tutorial shows how to design piped scrolls of frosting on a cake. Start with a tube 44 or 43 at one point and twist it at the top, allow the tail of icing to fall on the edges to cover the edges of the cake. Repeat the same process around the cake. Piped scrolls are easy enough to replicate, just watch this instructional video and find out how it's done.

How To: Easily build a rain barrel

A whole is drilled into the cap of a barrel with a 3 1/4 inch bit and another one an inch or more below the top and one of 3 inches width on the next side. Spreaded adapters ends are wrapped with plumbers tape; to prevent water leaks. The ends are then screwed together and placed into the top hole in the barrel. The spiget is held into the side hole with a piece of pvc pipe and a garden hose is attached. A funnel is made with a piece of window screen mesh slightly bigger than a pvc pipe it co...

How To: Install a toilet for your home

To install the new toilet you will need a putty knife, hacksaw, tape measure, adjustable wrench, level, sponge, and replacement wax seal. Before you begin removing the old toilet, turn off and disconnect the water supply to the toilet. Then flush the toilet to get the water out of it. Use a sponge to remove any remaining water in the bowl or tank.

How To: 4 Cheap & Easy Ways to Unclog Your Kitchen Sink Without Any Nasty Chemicals

Oh, boy. A stopped-up drain. It'll inevitably happen with any home plumbing system and your kitchen sink is no exception. That clog won't go away on its own and will require immediate attention to keep any standing water from rising. But you don't have to resort to calling an expensive plumber or using a bottle of hazardous chemicals. Using simple kitchen staples or common household objects, as well as some determination, you can unclog your kitchen sink on your own without paying a dime.

How To: Make your very own moonshine

In this tutorial, we learn how to make your very own moon shine. You will first need to take some sugar and mix it with some water. After these are combined, add in yeast to this mixture along with cinnamon and additional water. After this, you will need to pump some CO2 into the mixture and seal it tightly. Now, store this in a warm and dry place for 10 days without disturbing it. When finished, you will strain this mixture out and place into a pot with a pipe coming out of it. Once this is ...

How To: Craft a lizard out of foam & pipe cleaner

In this video, we learn how to craft a lizard out of foam and pipe cleaner. First grab your piece of foam and poke a hole into the front of it going through it, then through the back going all the way through. Next, poke the pipe cleaner through the holes so it looks like four legs. After this, poke a hole in the back to string the tail through. Poke a hole through the front and place a red pipe cleaner inside of it with a curl at the end to make it look like the tongue. To finish, draw on tw...

How To: Siphon gas out of a 3.8 GM engine

In this video tutorial you will learn how to siphon gas out of a modern 3.8 GM engine. The tools you need are a screwdriver, a clear plastic pipe and a container to hold the gas. Every fuel tank has a fuel inlet and outlet point. Remove the two clamps on the pipe connected to the fuel outlet point on the tank and fix the clear plastic pipe. The other end of the plastic pipe goes in to the container. Now locate the fuel pump relay in the relay box. In this engine it is relay number 19. Remove ...

How To: Unclog a sink in the bathroom or kitchen

In this Home & Garden video tutorial you will learn how to unclog a sink in the bathroom or kitchen. It's extremely simple. Put a bowl under the U joint. Unscrew the plunger rod located under the sink and pull it out. Then remove the sink blocker and remove any dirt from inside the pipe. Now unscrew the PVC U joint at both ends and remove it. This can be done with your hands. Most of the time this part is clogged. Clean it up. Then clean up the pipe coming down from the sink. Look from top an...

How To: Make an awesome tissue paper flower

In this tutorial, we learn how to make a tissue paper flower. You will need: pipe cleaners, scissors, and tissue paper (three different colors). First, twist three pipe cleaners together to make a stem. Next, cut your tissue papers all into the same size, mix colors to get a prettier flower. Now, layer the sheet and fold the papers as many times as possible. Cut the ends in a triangle shape, then spread the papers again and fold up again in the alternate direction. Now using your papers and p...

How To: Make a powerful bow for under 5 dollars

This is a tutorial that will show you how to create a powerful bow and for under $5. The material you'll need is 1 curved pipe, poly poli string, tape, scissors, and a knife. First you want to cut a slit and a hole on each end of the pipe and then add some tape underneath it to prevent it from splitting. Next, you want to line up the string with the pipe and cut it at that length. Also, you want to tie a knot at both ends of the strings and attach it by using the slits you made in the pipe. T...

How To: Solder copper pipes the right way

Soldering is a handy skill to have at your disposal. You probably don't want to jump right into it without practice on some scraps, but you can learn how to solder copper pipes together. You will need to make sure that all of the pieces you are working with are clean and dry first. You then need to apply flux to the end piece and slide the joint piece onto the pipe and hold it in place. Now you are ready to solder your pipes. This video will show you everything you need to know.

How To: Build a DIY wooden camera dolly with PVC railing system

If you need a dolly for your movie masterpiece, you don't need to go with a professional dolly system. You can save that money for your expensive actors and actresses by building your own DIY camera dolly on the cheap. You'll need some nuts and bolts, PVC pipes, scrap wood, drill bits and a drill, inline wheels and a hammer. This homemade camera dolly will cost you around 65 bucks.