How To: Create a Detachable DIY DSLR PVC Shoulder Rig
This video is going to teach you how to Create a DETACHABLE DIY Pvc Shoulder Rig Video: .
This video is going to teach you how to Create a DETACHABLE DIY Pvc Shoulder Rig Video: .
Video: .
In this video, Danny Lipford will show you how to make a punching bag with trash found at a construction site. First, a circle of plywood is cut out about one foot in diameter (in this video, a bucket is traced in pencil over the plywood). This is for the base of the punching bag. A large piece of PVC pipe is used for the center of the punching bag, which carpet padding is wrapped around to makeup the main part of the bag. Finally, duct tape is wrapped around the whole thing. Out of these ver...
This is a great instructional video on how to build an 8000 lumen CFL and makeshift rain shield. First you need build a PVC frame. For that you will need 3-3/4 'T'S, 4-12" 3/4 pipes,2-2 1/2 " pipes and 4-3/4 caps. You will also need 1-1 " 'T'. 2- 1" 1" pipes and 1-1"-3/4" reducer. Hold the job in a mechanical vice and cut the material into required sizes and make the snap fittings. Then friction fit the rest of the components into this stand. Then lastly you have to make the light box. That i...
This video tutorial is going to show you how to steady your shots with a homemade fig rig. The camera is mounted right in the middle of the top bar and it uses the iron as the balancing mechanism. The official fig rig is about $300. But, the one shown in the video will cost you around $10. Cut a PVC pipe about 2 feet in length and glue on two T joints on either end parallel to each other. Now fix the two feet into the T joints as shown in the video. The larger the camera, the longer will be t...
Follow along as Josh Gardner gives us step by step instructions on how to build a punching bag from trash.
This video shows you how to make your very own water filter. 1. 20mm PVC pipe for upper section larger debris.
Real rockets require top ingenuity from physics and engineering experts, but you can construct a smaller replica that costs almost nothing can can be made from materials you already have at home or can find at a hardware store.
In this tutorial, we learn how to make movie rain without getting wet. First, you will need to get a garden hose that has a spout on it and few pieces of PVC pipe. Connect the pieces of PVC pipe together, then stick the head of the hose to the pipe. Keep in mind that you will want to cut the pipe a bit shorter so it's easier to hold. Now, have someone hold up the pipe while you are taping and make sure to stay opposite of the way the wind is blowing. After this, you will have taped rain in a ...
Ben from mechanical mashup shows you how to make a fig rig for a small video camera out of PVC pipe. It gives an ingredient list and tells you the measurements of each piece you must cut. He recommends dry fitting everything at least once, to be sure everything goes together as it should. He then shows how the camera mounts on the rig. In transition of how-to's is a short scene relating to tools, with a man and a boy arguing over ownership. Then Dave shows how to neatly engrave your tools. He...
This step-by-step instructional video shows how you can do it yourself for your next party or event decorations. Air and helium filled balloons were used along with other easy to find supplies. Make your obsession for twisting balloons useful.
Take everyday sprinkler parts and form them into a high pressure rocket launcher that will shoot paper rockets nearly 300 feet!!! It's cheap to make and a lot of fun!
Watch this video tutorial to see how to build a fun foam boffer sword! These boffer swords for any of your larping needs!
Tim Carter of Ask the Builder, demonstrates how to drill a hole under a sidewalk, driveway or walkway so you can install an underground wire.
There are plenty of ways to create decent looking special effects on a budget. You can use basic, inexpensive materials to make ground explosions or realistic looking alien landscapes. But nothing says Hollywood quite like your own green screen.
Taking photos in the dark or in low-light settings can be tricky. Just using your normal flash can make your subject look washed out, but not using it can result in a totally dark photo with no subject at all.
Make your own armor with a weathered look out of Sintra (or expanded PVC foam). You'll need a heat gun, a padded cushion, paper towels, rub'n'buff in silver leaf, a knife, a marking pencil, water and a can of spray primer. Trace your piece onto the Sintra, then use the heat gun to shape it. Useful for costumes, Halloween or larps.
This tutorial shows you a very basic method to create an effective boffer sword using PVC pipe, a foam noodle, duct tape and some open-cell foam for a stabbing-safe tip. You're also shown a good method for constructing the hilt. This is a great tutorial for anyone looking to make a foam sword for their favorite boffer larp!
So, for this video you're gonna get a cool twofer! Are you making a cop movie? Or maybe a Sci-Fi military movie? Check out this awesome video, in it, you will learn how to make your own DIY grenades with some PVC pipe and also how to make those silver flying spheres from the Phantasm series, so cool!
Can't afford a camera dolly? Take a look at this instructional video and learn how to make your own low budget camera dolly. The materials you'll need to construct this dolly are:
You can make a rocket at home using these items found around the house. Icing sugar, measuring tape, a PVC pipe, black marker, hammer, flat headed bolt around 18 millimeters wide , mortar and pestle, drill, drill bit size 5 millimeter, potassium nitrate and kitty litter.
This homemade hairspray-powered PVC rocket takes less than an hour to construct and only costs about 20 dollars to make. Check out my video below for the step-by-step instructions on building your own backyard rocket, and follow the written guide below for reference.
What’s better in the summer than playing around in the water? Lounging in the pool, water balloon fights, and playing in the sprinklers helps us forget how much it sucks to be outside in 100+ degree weather.
When it comes to filmmaking, especially cinematography, indie filmmakers need to acquire a DIY sensibility in order to get their films made, because film equipment is nowhere near cheap. But DIY is.
This tutorial series shows you how to use Sintra (a type of PVC plastic that bends under heat) to make a piece of Spartan-style leg armor. This focues on making a shin guard, but you can use this method for any piece of armor you want to make.
Planning on shooting a low budget sci fi flick? The guys at Indy Mogul teach you how to make a cyborg arm and eye patch using a PVC coupler, coin tray, thin orange tubing, blue flash controllers, silver bubble wrap, duct tape, a rolodex, and costume jewelry.
The following video will demonstrate a simple process by which hard-boiled eggs can be scrambled prior to cooking, creating a deliciously blended center once finished.
Shoulder mounts are great for stability, but they can be pretty pricey. This DIY project by TheJamesTheatre is better in both aspects—it rests on both shoulders for extra stability, and it only costs 8 bucks to make. The frame is made of PVC with foam pieces from a pool noodle for cushion. All you need is a few connectors and the nuts and bolts to put it all together. You can find the full parts list on the About section on YouTube.
Costume parties are in full effect this weekend, so with that said, how cool would this look at your Halloween party? Instructables user castor009 made two holes in the head (one for inserting the PVC tube, the other where the liquid will spew out) and insert the pipe and tubing, then stuffed it to secure everything. He then fit the bottom tubing through a pencil holder and attached it to a water pump. Then just add whatever you want to serve at the party (I would suggest anything red or blac...
In the following video, I demonstrate how to build a simple device to increase the inertia of the wearers fist, allowing the easy destruction of concrete blocks.
If you've found your speakers to be lacking in the visuals department, this is just the mod for you. Using 3" PVC, you can turn your speakers into light-up glow rods that pulse to the beat of your music. You'll need some electrical skills and experience soldering to get this one together, but otherwise it's not all that complicated. The main components you are going to need are speaker drivers, PVC pipes, LEDs, and the necessary cabling for those devices. The device works best with higher vol...
Google Instant is one of Google's many search innovations, this one causing search results to emerge continuously below the search bar as you type. This can allow you to find more search results faster, and this video wills show you how it works, including how to turn it off if you decide you want Google to wait until you're finished typing before searching.
Want to film underwater, but can't afford the expensive professional camera rig? This tutorial shows you how you can construct your own functional underwater camera rig for about sixty dollars. You will need: small ankle weights, threaded seal tape, waterproof sealant, Velcro, a rubber washer, a sheet of plexiglass, PVC pieces, metal ring clamps, hot glue and a dremel.
If you prefer plastic Christmas greenery over real, we totally understand. While PVC isn't exactly renewable, it is eco-friendly in the sense that you don't need to unnecessarily chop down young evergreen trees and sprigs each year, only to throw them away after a week of use.
We understand if you prefer using fake evergreen sprigs and styrofoam berries in your house for Christmas decor rather than the real things, which tend to dry out in 1-2 weeks. But if you're lucky enough to have some really greenery growing outside your self, consider mixing real with fake for an everlasting display.
This video shows you how to take a pair of leggings (PVC works best, but any tight fabric will do) and turn them into a pair of trendy triangle cutout leggings. You will also need some thin ribbon and a sharp pair of scissors.
Construct your own shield for use in boffer combat! This tutorial shows you how to construct your own large punch shield out of several layers of blue camp foam, a length of PVC for the handle, a measuring tape and some DAP adhesive.
Now you too can build your own prop of eldritch horror! Guaranteed to induce a SAN check in anyone who sees it, this tutorial shows you how to build a set of flexible Cthulhu tentacles out of one inch furniture foam, half inch furniture foam, steel wire, pantyhose, one inch PVC tubing, epoxy and a jar of latex.
Knitting when you're sitting at your table is usually a cinch, since you can rest your elbows on the table when you're tired and also place your knitting needles and yarns closeby within reach. But staying in one place all day long can be boring.
Instead of hiring a professional plumber, get free advice from one in this video presented by Fine Home Building. Follow a professional plumber as he shows you how to replace a kitchen sink trap. You'll learn how to layout, cut, and cement PVC pipe.