To solder copper pipes, start by using a sharp blade and scrape the end of the pipe you are going to solder. This will get all the burrs off of the pipe. Next, take some steel wool and clean the pipe so that it is nice and clean and shiny. The next step is to apply some flux. Use a rag to apply the flux to the end of the pipe. You want to make sure that the flux goes all the way around the pipe. After putting flux on the two pieces of pipe, put them together using the fitting. Take the blowto...
Making and sewing piping can be an easy and fun sewing project. Get tips from our expert on fabric piping in this free sewing video series.
Watch this lampworking video series to learn how to make a glass blue tubing enclamo pipe. This style of pipe is nice because of the way it lays down - it doesn't look like a typical pipe.
Learn how to make a bike repair stand with this video! Create the legs: 1. Two sets of 8 and 10 inch piece of steel pipe, a 90 degree angle, an end cap and a T pipe are the starting materials. About 0.5 inch diameter pipe is fine for the project.
In this video tutorial, viewers learn how to add strength to a landscape patio wall. For reinforcement, users should insert metal pipes down through the wall. To do this, users will need a sledgehammer, 1/3" pipe and a large diameter pipe cutter. Determine the length of the pipe by adding 2 feet to the actual length of the wall. Cut the pipe to the length and insert the pipe down through a large diameter hole on the wall. Remove the surrounding blocks and use the sledgehammer to drive the pip...
This simple how-to from Buildpedia shows every DIYer how to "sweat pipe", meaning, how to solder it together. This is a simple technique that's easy to get the hang of. You'll need a solder kit, the pipes want to solder, an aceteline torch and a few other things.
Learn how to make this spooky, amazing floating static orb. This is so simple, and so cool. It uses static electricity to make a tinsel orb levitate above a PVC pipe. We've gotten the orb to float for over 10 minutes. We just discovered you can use a regular balloon instead of the PVC pipe, but we like the pipe best. Watch the video, and then make your own!
Tired of soldering? Well, there's a solder-less solution to joining pipes together. Check out this handy video tutorial on how to join copper pipe with "Just For Copper" pipe glue. Just For Copper is a solderless bonding solution for copper pipes and fittings. This is very useful in areas where a blowtorch cannot be used.
Has your child been in love with fish since "Finding Nemo?" Learn how to make pipe cleaner fish from a professional art instructor in this free crafts video series.
Everything you ever wanted to know about making arts and crafts projects with pipe cleaners in this free arts and crafts video series for kids taught by and expert.
In this tutorial, we learn how to install dual exhaust on your tractor! First, find the exhaust strip on the tractor, then detach the muffler and slip the regular pipe into the muffler. After this, get a 3/4" pipe and slip it up into the other pipe and well around it. It should come to the bottom of the tractor. Next, take a bushing and connect it to the elbow pipe. Connect a short pipe and connector to this, then connect a long straight pipe that goes into the dead center of the bottom of th...
In this tutorial, we learn how to straight pipe your small tractor engine. First, insert a one inch screw pipe to your exhaust, then connect pipes into it so it connects to the back of the vehicle. You will need to install several elbow pipes as well as longer straight pipes. The pipes should reach the end of your tractor out of the tires. Make sure it's secured tightly to the floor boards and screwed in on the bottom of the tractor. You can experiment with different types and shapes of pipes...
This video will show you how to make flowers out of pipe cleaners. To start you'll need five pipe cleaners. The video shows the basic steps of connecting the first two pipe cleaners by twisting together the ends. Then pipe cleaners are bunched together and wrapped by another pipe cleaner. This creates the petals and the stem that extends downwards. After the petals and stem are shaped correctly, a green pipe cleaner is wrapped around the yellow stem to give it a realistic green appearance. Fi...
In this video, we learn how to cut plastic push-fit pipe. Make sure you never use a hack saw to cut the push-fit pipe because it can damage the O-ring in the connector. What you need is a pair of dedicated plastic pipe cutters. Once you have this, put your pipe in the middle of the cutters and then push down on the handles. After this, your will cut the pipe and it will com out nice and clean. From here you will be able to fit a connector into the pipe and continue to use it rather than ruini...
Follow this video to learn how to use copper push-fit fittings to connect piping. 1. Sometimes we connect pipes by means of push-fit fittings which are not very appealing to look at since they are of a different color and material and so do not match with the pipe. However a good alternative is to choose copper push-fit fittings rather than plastic ones. Copper push-fit fittings would be similar to the pipe itself. 2. Open the pipe and ensure that it is clean before fixing the fitting by simp...
About a quarter of a million homes sustain damage from broken pipes every winter. Here's how to avoid a similar fate. Watch this video to learn how to prevent pipes from freezing.
Sewing a round pillow with piping is a fun challenge for a beginning seamstress. Learn to sew a round throw pillow with this free sewing video series.
Drip, drip, drip. Other than maybe a fly buzzing around your head in concentric circles, a leaky pipe is possibly the most annoying thing you can hear in the middle of the night when you're trying to get some sleep. Thankfully, though, a leaky pipe is one of the easiest plumbing problems to fix all by your onesies.
Have a PVC pipe that's in an awkward position and you're having a hard time reaching it to cut it? This video demonstrates that cutting a PVC pipe is as simple as wrapping a nylon string around it. Now you can cut through a PVC pipe without a saw or knife.
This tutorial shows you how to make a boffer larp safe mace. Get some PVC pipe, a foam noodle you can get at a drug store, and some soft foam for the head. Then cover your pipe with pipe insulation and sheath the weapon in latex.
If you live in an area where it gets really cold during winter, you may or may not know the importance of protecting your pipes. Not covering them with proper insulation can result in frozen pipes that are a pain to fix and can cost you a lot of money. So in this tutorial, you'll be finding out how to properly insulate your pipes for the winter months. Good luck and enjoy!
Learn how to cut and join plastic pushfit piping using pushfit connectors and compression fittings. While plastic piping has its drawbacks and, depending on its application, actually be carcinogenic, it is, at least, very easy to work with. For step-by-step instructions on cutting and joining plastic pushfit pipes, watch this home plumbing tutorial.
Learn how to sweat copper pipe properly with this handy video. Connect two pieces of pipes with solder.
Teflon tape or pipe dope can be used to create a seal on black iron pipe. Tim Carter of AsktheBuilder.com demonstrates how to do the job right and shares some helpful tips. This black iron pipe is used to transport natural gas to your furnace, water heater and stove. This pipe has threaded fittings at the connection point which need to be sealed with pipe dope or Teflon tape. Teflon tape should be wrapped onto the male end of the pipe in a clockwise direction. Pipe dope has the consistency of...
These are simple instructions on how to construct a PVC didgeridoo. You must work in a well ventilated area as you are dealing with heat and PVC fumes. You need a heat gun, pipe clamp, screwdriver, pipe cutter, dremel, PVC pipe, buffing bit and bucket of water. This is a detailed process of digeridoo making.
Piping cones are indispensible when applying flowers, leaves, and frilly trims on cupcakes and cakes, and cones with particularly fine points can be used to apply henna in intricate patterns.
How to make mini Christmas wreaths out of pipe cleanersIn this video we are about to see how to make mini Christmas wreaths out of pipe cleaners. To start with we get colors of pipe cleaners. Now take them of equal length and twists their ends together so that they don’t come off. Start braiding from the attached ends. The art of braiding is very easy. Just take the middle over the left and the middle over the right. Repeat the process till the end of the pipe cleaners. Leave out a small port...
In this video "A better way" presenter Chuck Miller demonstrates a method of how to create a job site pipe holder (clamp hold-down) as opposed to a c-clamp, bar clamp or blocks of wood. It involves use of a pipe flange of the same diameter as the pipe being held. It shows you how to drill a hole into the top of your workbench and install the pipe flange. The video finally demonstrates how to use the pipe clamp in order to install a work-piece and clear the clutter from your work bench. The ti...
A frozen pipe doesn’t have to mean major trouble. You can keep your water flowing all winter long. You Will Need
Watch as a seasoned DIYer demonstrates the steps necessary to sweat (join and solder) copper pipes, including how to prepare them, what tools to use, and how to fix any mistakes you may make, in this free online video about home repair.
Poke, jab, and stab your opponent without taking out an eye. You Will Need
Cupcakes are delicious as they are, but they're even more wonderful and charming when you pipe a beautiful design on top with frosting.
Tim Carter of Ask the Builder, demonstrates how to drill a hole under a sidewalk, driveway or walkway so you can install an underground wire.
This video tutorial is in the Electronics category which will show you how to solder stainless steel. For this you will need silver bearing solder. Harris #8 StaBrite is good, but it is expensive. Plumber solder works fine, but make sure it has silver in it. Use Harris Stay Clean liquid flux. All the surfaces have to be clean and sanded. In this video a pipe is being soldered to a metal sheet. Apply some liquid flux to the outside of the pipe to be soldered. Make a neutral flame, heat the pip...
In this tutorial, we learn how to make movie rain without getting wet. First, you will need to get a garden hose that has a spout on it and few pieces of PVC pipe. Connect the pieces of PVC pipe together, then stick the head of the hose to the pipe. Keep in mind that you will want to cut the pipe a bit shorter so it's easier to hold. Now, have someone hold up the pipe while you are taping and make sure to stay opposite of the way the wind is blowing. After this, you will have taped rain in a ...
In this tutorial, we learn how to make a lily out of paper and pipe cleaner. First, lay your hand flat on a piece of copy paper. Next, trace your hand with a pen or pencil, then cut it out with scissors. Now use a pencil or pen to curl the ends of the fingers you just cut out. After this, combine two pieces of gold pipe cleaner together and bend in half. Then, place a green pipe cleaner in the middle and make a twist to keep in place. To finish, wrap your paper hand cut out around the gold pi...
In this tutorial, we learn how to craft a penguin out of pip cleaners. First, grab a pencil and wrap white pipe cleaner around the top. Now, wrap black around the pencil as well, and squish them both together. Slide them off, then take an orange pipe cleaner and fold it in half. About 2 rings from the top of the black, poke the orange through that will be the beak. On the bottom, twist the orange pip cleaner together to make penguin feet, then clip off any excess pipe cleaner. Now, take black...
In this tutorial, we learn how to craft a snake out of a pipe cleaner. First, you will take three pipe cleaners and twist their ends together, then stick a large pom pom in between the pipe cleaners. Then do a braid with the pipe cleaners until you reach the end, and then twist the end together. Then, take some googly eyes and glue them onto the pom pom. You can now twist the snake to make it look like a rattle snake and add a piece of red felt to make the tongue. This is a fast and easy proj...
In this video tutorial, viewers learn how to build a green screen. The materials required for this project are: two 10 ft long PVC pipes, measuring tape, saw, duct tape and pipe elbows and couplings. Begin by marking the two PVC pipes with 6 ft on one side and 4ft on the other. Then cut the PVC pipes in half. Now connect the frame together with the pipe elbows and couplings. Build support to the fame by adding some duct tape. Finish by attaching the green cloth on the frame and tape it at the...
Building your own skateboard half-pipe in the confines of your own backyard, is a great thing for anyone who enjoys a little challenge. Certain weather conditions or travel issues, can make it difficult for some skateboarders who are looking to spend some quality time trying new tricks and perfecting skills. In this tutorial, you'll find out how to build a skateboard half-pipe with the help of former NFL star, Michael Strahan. So good luck and enjoy!
